解讀燃氣熱風爐怎麼點火？安全詳細步驟！

對於燃氣熱風爐成都收賬使用來說，點火是一個很重要成都找人公司步驟，正規成都收賬點火步驟為：步把熱風爐收賬點火口打開，但是之前你一定要打開助燃風機，還有助燃風機成都找人公司放散。因為熱風爐的在沒有點燃之前所有助燃風閥門都是關閉的，如果不開放散容易憋壞助燃風機，還有切斷煤氣閥門。
For the use of gas hot stove, ignition is an important step. The normal ignition step is to open the ignition port of the hot stove step by step, but before you must turn on the combustion fan, there is also the dissipation of the combustion fan. Because all combustion-supporting air valves are closed before the hot stove is ignited, if it is not opened, it is easy to choke the combustion-supporting fan, and cut off the gas valve. 第二步開始點爐，先把木材上到上煤油，然後把淋上煤油的木頭扔進熱風爐內，放爐膛空間的3分之2就好，然後準備火佈，找跟細鋼筋，然後把火佈用鋼筋塞進爐膛，點火的時候助燃風是小開狀態的，開大瞭火就吹滅瞭。
The second step is to start the stove, first put the wood on kerosene, then throw the wood sprinkled with kerosene into the hot blast stove, put two-thirds of the space in the stove, then prepare the fire cloth, find the fine steel bar, and then put the fire cloth into the stove with steel bar. When the fire is ignited, the combustion-supporting wind is in a small state, and the fire is blown out.
第三步，裡面木頭燃燒以後觀察孔看裡面的燃燒情況，這個時候別關閉點火口！一開始燃燒時火是橙紅色的，這個時候還得一個人負責開煤氣手動閥門。一定要輕輕開！開大瞭裡面沒有氧氣火就滅瞭！當觀察口的人看到裡面火苗微藍色，馬上停止手動煤氣閥門，先燒一會，燒一會火也陸續變大瞭！然後繼續加大手動煤氣閥門，加手動煤氣閥門的煤氣時，要加點助燃風瞭。因為煤氣大瞭，氧氣便會稀薄，火還是會熄滅，因此要給點助燃風！
The third step is to observe the burning situation in the hole after the wood inside burns. Don't close the ignition port at this time! The fire was orange red at the beginning of the combustion, and at this time a man had to turn on the gas manual valve. Be sure to open it gently! When it's bigger, there's no oxygen in it, and the fire goes out! uuuuuuuuuu When the observer sees the light blue flame inside, he immediately stops the manual gas valve and burns it for a while. After a while, the fire becomes透水地坪 bigger and bigger. Then continue to increase the manual gas valve, gas with manual gas valve, to add ignition air. Because the gas is big, the oxygen will be thin, the fire will be extinguished, so we need to ignite the combustion-supporting wind!
第四步，進入操作室，觀察廢氣儀表！正常廢氣不能操過350你應該知道的，等廢氣溫度升起來一些應該上去加些煤氣和助燃風瞭，就是這樣一點點的加一點點的調試，直到觀察口內看不到火苗實閃動，取而代之的是一片橙紅色的火焰！根本看不到火苗！好瞭這個爐也就燒的差不多瞭！進操作室！等廢氣溫度達到要求！就悶爐！然後再點二號！就ok瞭！
Step 4: Enter the operating room and observe the exhaust gas meter! Normal exhaust gas can not operate over 350. You should know that when the exhaust temperature rises, some gas and combustion-supporting air should be added. That is to say, a little bit of debugging should be added until the fl印花地坪ames can not be seen in the observation mouth, instead of an orange-red flame! No fire at all! Well, this stove will burn almost! Into the operating room! Wait until the exhaust temperature reaches the requirement! Close to the stove! And then order number two! uuuuuuuuuuuu OK!
熱風爐點火後必須密切觀察熱風進出風溫度，及燃燒器運行情況，如發現異常要及時匯報處理。燃氣熱風爐配置進口品牌燃燒器，自動化程度高，按照控制器指令自動吹掃，電子自動點火，自動燃燒，風油（氣）自動比例調節，性能安全穩定，燃燒效果好。並有熄火保護裝置，保證安全運行。此外，火管內插有阻燃擾流片，減緩排煙速度，加強換熱，煙室排出的煙氣溫度低，減少熱損失，節省燃料。
After ignition, the temperature of hot air inlet and outlet and the operation of burner must be closely observed. If any abnormality is found, it should be reported and handled in time. Gas hot blast stove is equipped with imported brand burner with high degree of automation, automatic purging, electronic automatic ignition, automatic combustion, automatic proportional adjustment of air-oil (gas), safe and stable performance, good combustion effect. It also has fire extinguishing protection device to ensure safe operation. In addition, a flame retardant spoiler is inserted in the fire pipe to slow down the smoke exhaust speed, enhance heat transfer, lower the temperature of the smoke discharged from the smoke chamber, reduce heat loss and save fuel.