如何使熱風爐的烘幹效率達到最高？

熱風爐是一種結構簡單，性能穩定，維修方便成都收賬幹燥設備，廣泛應用於水泥生產過程。我們在改革中一般應與“風，根據修改消防，材料”成都找人公司平衡，所以具體到每個部分熱風爐如何改革，我們應該註意什麼？一般成都收賬旋轉幹燥器升降機改造時應註意以下幾點：
Hot blast stove is a drying equipment with simple structure, stable performance and convenient maintenance, which is widely used in cement production process. In general, we should balance the reform with "wind, fire protection according to modification, material", so how to reform each part of hot stove, what should we pay attention to? In general, the following points should be noted when upgrading the rotary dryer. 1、熱空氣和材料收賬接觸面積。材料應盡可能均勻地分佈在一段烘幹熱風爐筒，與熱空氣充分接觸成都找人公司材料，消除風洞材料和不均勻分佈的原因。
1. Contact area between hot air and material. Material should be distributed as evenly as possible in a section of drying hot blast stove. Material in full contact with hot air can eliminate the cause of material and uneve印花地坪n distribution in wind tunnel.
2、註意熱空氣和材料的接觸時間。我們要接觸時間盡可能延長材料和熱空氣幹燥，以達到最佳的效果。
2. Pay attention to the contact time between hot air and materials. We should contact time to extend the material and hot air as far as possible to achieve the best results.
3、為瞭使物料在運動狀態盡可能，將運動中的氣體流中的旋轉幹燥器，陽板，管壁，陳舊的消除。每單位時間的材料盡可能的運動。
3. In order to make the material move as far as possible, the rotary dryer, the positive plate, the pipe wall and the obsolete elimination in the moving gas flow are eliminated. Material per unit time is as fast as possible.
4、為瞭便於生產，安裝，維修，更換。
4, in order to facilitate production, installation, maintenance, replacement.
5、要註意幹燥機裡物料在預熱段，幹燥，降速幹燥行為。
5, attention should be paid to the preheating, drying and drying behavior of materials in the dryer.
應註意升降板重建的五種以上，我們可以把升降機步弧式升降機。走弧形升降板上有非常強的材料的適應性，煤泥等粘性物料不易粘在升降板，在棚板材料的運動是一個輕松自由的運動狀態。同時，根據每個電弧改變不同的要求，如在預熱段材料的水分含量高，我們可以提高電弧以防粘材料。
Attention should be paid to more than five kinds of lifting board reconstruction, so we can lift the lift step arc lift. The arc-shaped lifting board has very strong material adaptability. The sticky materials such as slime are not easy to stick to the lifting board. The movement of the shed board material is a relaxed and free movement state. At the same time, according to the different requirements of each arc, if the moisture content of the material is high in the preheating section, we can improve the arc to prevent sticking materials.
我們正在安裝弧形升降板，為瞭使軸升降板和回轉幹燥機筒形成夾角，最佳傾斜角度大於或等於烘幹機，進料端低，一些高排放端，形成在筒體內的螺旋。同時，間隔必須每層之間的優勢，和一層升降機，升降板間距下一層之間的對準。螺旋升降機的設計，可以在缸使材料螺旋運動，從而延長物料在熱風爐筒體的保留時間。
We are installing arc-shaped lifting plate, in order to form an angle between the shaft lifting plate and the rotary dryer barrel, the optimum inclination angle is greater than or equal to the dryer, the feeding end is low, and some high emission ends are formed in the spiral of the barrel body. At the same time, the spacing must be between the advantages of each layer, and the alignment between one layer of elevator and the next layer of elevator spacing. The design of spiral elevator can make the material spira环氧地坪l in cylinder, thus prolonging the material retention time in hot blast stove barrel.