耐磨环氧地坪出現伸縮縫怎麼處理？

采用耐磨环氧地坪是為瞭防滑，提高安全性，但不是是施工工藝有問題還是所使用的使用材料有問題，耐磨环氧地坪在施工後出現瞭伸縮縫，這樣影響瞭使用性能，那麼這樣的情況我們怎麼處理呢？直接簡單的處理方式就是在耐磨地坪施工後進行伸縮縫的切割，但要掌握好相關的操作流程，以免適得其反。首先是要掌握好切割耐磨地坪伸縮縫的時間，切早瞭容易崩邊，但切瞭就沒有用瞭，一般都是在施工完工後的第二天進行。
Wear-resistant epoxy flooring is used to prevent skid and improve safety, but it is not the construction technology or the use of materials that have problems. After construction, expansion joints appear on the wear-resistant epoxy flooring, which affects the performance of use. So how can we deal with this situation? The direct and simple way is to cut the expansion joint after the construction of the wear-resistant floor, but to master the relevant operation process, in order to avoid the opposite. First of all, we should grasp the time of cutting the expansion joint of wear-resistant floor, cutting early and easy to collapse, but cutting is useless, usually on the second day after the completion of construction.
除合理掌握時間外，切割耐磨地坪伸縮縫的順直也很關鍵，而這主要取決於彈線和切割兩方面，可以借助先進的儀器彈線，並由技術熟練的工人切割，以此保證切割出來的伸縮縫是順直的。
In addition to reasonable control of time, the straightness of the expansion joint of wear-resistant floor is a彩色沥清地坪lso crucial, which mainly depends on the elastic line and cutting. It can be cut by skilled workers with the help of advanced instruments, so as to ensure the straightness of the expansion joint.
關於切割伸縮縫尺寸是這麼規定的，其寬度一般為3-5mm，深度一般為水泥混凝土厚度的1/3-1/2，可以按柱距或設計圖紙要求為準。完成對耐磨环氧地坪的伸縮縫切割之後，應立即將在伸縮縫兩側產生的水泥灰漿清除，避免幹燥後難於清理，必要時可用水沖洗，待幹燥後再根據設計要求填縫。
As for the size of the cutting expansion joint, the width is generally 3-5mm and the depth is generally 1/3-1/2 of the thickness of cement concrete, which can be based on the requirements of column spacing or design drawings. After cutting the expansion joint of the wear-resistant floor, the cement mortar produced on both sides of the expansion joint should be removed immediately to avoid being difficult to clean after drying. When necessary, it can be washed with water and then filled according to the design requirements after drying.
在填縫之前應先在耐磨环氧地坪伸縮縫底部填塞海綿膠條，頂部用聚氨酯填縫膠專用打膠槍均勻填充，註意填充均勻、飽滿，不得有空洞、斷頭等現象。同時，要避免對伸縮縫邊緣及以外的區域造成污染，以免影響耐磨环氧地坪整體的質量。
Before filling, sponge tape should be filled at the bottom of the expansion joint of the wear-resistant epoxy floor. The top of the joint should be filled evenly with a special polyurethane filler gun. Pay attention to filling evenly and satisfactorily, and there should be no holes or broken ends. At the same time, we should avoid polluting the edge of expansion joint 印花地坪and other areas, so as to avoid affecting the overall quality of wear-resistant floor.