如何選擇合適的环氧地坪及驗收標準

為瞭幫助使用环氧地坪裝飾保護塗料的顧客正確地選擇环氧地坪的種類和有效控制建設成本，建議顧客超好從以下幾個因素入手：一、機械性能要求：主要以下三個方面：1. 耐磨性：环氧地坪在使用時會有哪些車輛行走; 2. 耐壓性：环氧地坪在使用時會承受多大荷載;3. 耐沖擊性：沖擊力是否會引起地坪面剝離; In order to help customers who use floor decorative protective coatings correctly select the types of floor and effectively control construction costs, it is suggested that customers should start with the following factors: 1. mechanical performance requirements: the following three main aspects: 1. wear resistance: which vehicles will walk when using epoxy floor; 2. pressure resistance: epoxy When the floor is used, it will bear much load; 3., impact resistance: will the impact force cause the peeling off of the terrace surface? 二、化學性能要求 Two. Chemical performance requirements
主要考慮以下兩個方面： The following two aspects are mainly considered:
1. 耐酸堿性：使用時腐蝕性化學物質的種類及濃度。 1. acid and alkaline: the type and concentration of corrosive chemicals used.
2. 耐溶劑性：使用時溶劑類型及接觸時間。 2. solvent resistance: solvent type and contact time.
三、樓層位置狀況 Three. Floor location status
根據环氧地坪是在地下樓層還是地面樓層的位置，確定是否需要防潮處理或選擇特殊防潮地坪? According to the location of the epoxy floor in the underground floor or the ground floor, is it necessary to determine whether moisture-proof treatment or special moisture-proof floor is needed?
四、基面狀況 Four. Base level situation
1. 基層強度：一般要求抗壓強度≥20Mpa 1. base strength: General requirements, compressive strength is greater than or equal to 20Mpa
2. 平整度：是否需要用环氧砂漿修補? 2. Flatness: is it necessary to repair with epoxy mortar?
3.地面施工前一般需要用自流平處理 3. self leveling is usually required before surface construction.
五、美觀要求 Five, aesthetic requirements
1. 顏色要求：是否需要顏色劃分區域? 1. color requirements: do you need a color division area?
2. 亮度要求：是選擇啞光還是亮光? 2. brightness requirement: choose matte or bright?
3. 平整度要求：是否對地坪的平整度有要求? 3. flatness requirement: is there any requirement for the smoothness of the floor?
六、安全性要求 Six, safety requirements
如果地坪處在油漬环境或坡道處，則需要選擇防滑地坪;如果在加油站，油庫等特殊場所需要選擇防靜電、防爆的。 If the floor is located in the oil-stained environment or ramp, it is necessary to choose the anti-skid floor; if the gas station, oil depot and other special places need to choose anti-static, explosion-proof.
七、施工工藝： Seven. Construction technology:
1、基面處理; 1, base surface processing;
2、塗刷封閉底漆; 2. Brush the primer.
3、批刮膩子; 3, batch scraping putty;
4、打磨、吸塵; 4, grinding and vacuuming;
5、塗刷色漆; 5, brush the paint.
底漆采用环氧樹脂底漆主劑：固化劑，調制均勻固化10分鐘左右，用羊毛滾筒滾塗一遍，底漆主要是封閉基礎層，封閉水氣及灰塵 Primer is epoxy resin primer main agent: curing agent, modulation uniform curing for about 10 minutes, with wool drum rol环氧地坪l coating once, primer is mainly to seal the foundation layer, seal water and dust.
6.填補處理 6. fill in
用环氧漆石英砂調制环氧砂漿，填補伸縮縫及破損處 Epoxy mortar is modulated with epoxy sand and quartz sand to fill the expansion joint and damage place.
7.批刮中層 The 7. batch scraping middle layer
8.上环氧樹脂面漆 8. epoxy top coat
9工程養護 9 engineering maintenance
八、技術指標： Eight, technical indicators:
幹燥時間 表幹 ≤4 Drying schedule is less than 4.
實幹 ≤24 Actual work is less than 24
附著力(級) ≤1 Adhesion force (grade) is less than 1
鉛筆硬度 ≥2H Pencil hardness is more than 2H
耐沖擊性 50通過 Impact resistance 50 passes
柔韌性 1㎜通過 Flexibility 1 pass
耐磨性(750g/500R，失重g)≤0.03 Wear resistance (750g/500R, weightlessness g) is less than 0.03.
耐水性 48小時無變化 No change in water resistance for 48 hours.
耐30%硫酸 7天無變化 Resistant to 30% sulfuric acid for 7 days without change.
耐40%氫氧化鈉 7天無變化 40% NaOH resistant for 7 days without change.
耐汽油 120# 7天無變化 Gasoline resistant 120# remained unchanged for 7 days.
耐潤滑油 7天無變化 No change in lubricating oil for 7 days.
环氧地坪驗收標準
對於次做环氧地坪的用戶來說，环氧地坪施工完畢以後，不知道該如何驗收，环氧地坪公司介紹一下环氧地坪的驗收標準，供用戶參考. For the users who make epoxy flooring next time, after the construction of epoxy flooring is finished, they do not know how to accept it. Yunnan Qiancai Flooring Company introduces the acceptance criteria of eptance of epoxy flooring for users'reference.
表面性能： Surface properties:
1、环境溫度為25℃時，施工後2-3天應達到實幹，即硬度達到完成固化的80%左右; 1. When the ambient temperature is 25 C, the hardness should reach about 80% of the solidification after 2-3 days of construction.
2、表面不能出現發粘現象; 2, the surface can not appear sticky phenomenon;
3、氣泡：平塗型、砂漿型無氣泡，自流平允許1個小氣泡/10平方米; 3, bubble: flat coated, mortar type no bubbles, self leveling allows 1 small bubbles /10 square meters;
4、流平性好，無鏝刀痕，大面積接口處基本平整; 4, good leveling, no trowel marks, large area of the interface is basically smooth.
5、無浮色發花，顏色均勻一致，大面積接口處允許有極不明顯的色差; 5, no floating color and flower, uniform color, large area interface allows very insignificant chromatic aberration;
6、無粗雜質，但允許有空氣中的浮塵掉落在造成的極小缺陷; 6, there is no coarse impurity, but it allows the floating dust in the air to drop into the minimal defect.
7、自流平表面應平整平滑，光澤度應達到設計要求(高光澤≥90、有光≥70、半光50～70)，平塗型為有光、水性為半光～無光; 7. The self-leveling surface should be smooth and smooth, and the glossiness should meet the design requirements (high gloss (> 90), glossy (> 70), semi-glossy 50-70), and the flat coating type should be glossy and water-borne semi-glossy to non-glossy.
8、桔皮、砂漿防滑面效果應很明顯。 8, orange peel and mortar anti slip surface effect should be very obvious.
機械型能(完成固化後)： Mechanical type (after curing):
1、硬度：無指甲壓痕或很快恢復; 1, hardness: no nail indentation or rapid recovery;
2、耐磨性:≤0.024g(500g/1000r); 2, wear resistance: less than 0.024g (500g/1000r);
3、中等強度、中等濃度堿及常見溶劑擦洗無影響印花地坪; 3. Moderate strength, moderate concentration of alkali and common solvents have no effect on scrubbing.
4、濕拖把拖過或水沖洗表面不變色; 4, wet mop drag or wash the surface of the water does not change color;
5、塗膜無脫層(咬底)、鼓起、露底等現象 5, no delamination (bite bottom), bulge and bottom phenomenon.