工業廠房中的环氧地坪的保養大全

文章时间:2018-11-01 23:02:14   浏览次数:1138

环氧地坪是一種高強度美觀潔凈的地面,不僅擁有較高的附著力和負載性,並兼具強韌耐磨、平整光潔及成本經濟等優點,受到許多廠商的青睞。幾乎所有的現代化工廠都會選擇不同的环氧地坪塗裝系統以適應其不同的环境需要。根據用途要求有多種环氧地坪系統,如電子廠房常用的环氧防靜電地坪,食品廠常用聚氨酯砂漿地坪,煙廠常用环氧彩砂地坪等。但是長時間的負重載多少會對环氧地坪造成一定的損害,正確的使用方法和維護保養可使地面常保如新,並且可以保長使用年限。那麼,如何保養和維護环氧地坪呢?
Epoxy floor is a kind of high strength, beautiful and clean ground. It not only has high adhesion and load, but also has the advantages of toughness, wear resistance, smoothness, cleanliness and cost-effectiveness. It is favored by many manufacturers. Almost all modern chemical plants will choose different floor painting systems to meet their different environmental needs. According to the application requirements, there are many kinds of floor systems, such as epoxy anti-static floor commonly used in electronic factory, polyurethane mortar floor commonly used in food factory, and epoxy coloured sand floor commonly used in tobacco factory. However, long-term load-bearing will do some damage to the epoxy floor. Correct use and maintenance can keep the ground fresh and prolong the service life. Then, how to maintain and maintain the epoxy floor?
环氧地坪漆廠傢給您提出在使用环氧地坪的具體建議:
The epoxy floor paint manufacturer gives you specific suggestions on the use of epoxy floor.

1、新建环氧地坪施工完畢後,在保養期內切勿使用,養護5-7天,避免其他液體浸潤表面,並須加強通風設備及防火措施;
1. After the completion of the construction of the new epoxy floor, do not use it during the maintenance period. Maintain for 5-7 days to avoid other liquid infiltration on the surface, and strengthen ventilation equipment and fire prevention measures.

2、环氧地坪使用,生產人員不準穿有鐵釘的皮鞋在上面行走,建議現場人員換成橡膠底鞋或者潔凈鞋;一切工作器具都須有固定專用車架安放,嚴禁帶有銳角的金屬零件等物件碰撞地面,造成地面塗層損壞。
2. When using epoxy flooring, production personnel are not allowed to walk on it with nailed leat透水地坪her shoes. It is suggested that field personnel should replace rubber soles or clean shoes; all working instruments should be installed with fixed special frame, and metal parts with sharp angles should be strictly forbidden to collide with the ground, causing damage to the ground coating.

3、生產車間廠房內現場安裝設備時,在接觸环氧地面的支撐點應有厚橡皮等軟件材料墊妥,嚴禁用鐵管等金屬在环氧地面上接拖設備;叉車、鏟車卸貨時註意貨物平放,避免貨物側侄、拖、拽刮傷环氧地面,各車輛在運行時盡量避免剎車,在环氧上急剎車很容易產生胎痕,而且還清理不掉。
3. When installing equipment on site in workshop workshop, the support points of contacting epoxy ground should be padded with thick rubber and other software materials, and it is strictly forbidden to use metal pipes to connect and tow equipment on epoxy ground. Forklift truck and forklift truck should pay attention to placing cargo when unloading, so as to avoid cargo side nephew, towing and scratching epoxy ground, and all vehicles run out. Avoid braking. Brake on epoxy is easy to produce tyre marks, and it can not be cleaned up.


4、生產車間廠房內环氧地坪有損壞,及時使用环氧地坪漆修補,以免油污通過損壞處滲透到水泥裡,造成印花地坪大面積塗料脫落。
4. If the epoxy floor is damaged in the workshop, the epoxy floor paint should be used to repair it in time so as to prevent oil pollution from penetrating into the cement through the damaged area and causing a large area of paint to fall off.

5、現場內大面積清洗环氧地面時,不要用強化學溶劑,一般使用洗滌劑、肥皂液、清水等,用清洗機進行,或者打蠟也可以。
5. When cleaning the epoxy floor in large area on site, do not use reinforcement chemical solvent. Usually use detergent, soap solution, water, etc. It can be carried out by washing machine or waxing.