怎麼檢驗环氧地坪塗料黏度的方法

隨著环氧地坪使用范圍的擴大，在各停車場、廠房、醫院、工業等區域都可見。在环氧地坪施工完成後我們一定要註意監測环氧地坪塗料的黏度，环氧地坪漆塗料的黏度程度是保證环氧地坪施工後的質量和使用壽命。我們在測量环氧地坪漆黏度時一定要註意以下幾點，否則很難操作。在檢測地坪漆黏度上切不可大意，以免造成施工完成後的質量問題等因素。
With the expansion of the use of epoxy floor, it can be seen in parking lots, factory buildings, hospitals, industries and other areas. After the construction of epoxy flooring, we must pay attention to monitoring the viscosity of epoxy flooring paint. The viscosity of the flooring paint is to ensure the quality and service life of the epoxy flooring after construction. When we measure the viscosity of floor paint, we must pay attention to the following points, otherwise it is difficult to operate. In testing the viscosity of floor paint, we must not carelessly, in order to avoid the quality problems after the completion of construction and other factors. (1)測定的規定溫度應在21-25℃之間。因為溫度過高的話測定的黏度就比較低，而溫度過低相對黏度就比較高，沒有標準值，所以在溫度上一定要把握好。
(1) The prescribed temperature for determination should be between 21 and 25 degrees Celsius. Because if the temperature is too high, the measured viscosity will be relatively low, and if the temperature is too low, the relative viscosity will be relatively high. There is no standard value, so we must grasp the temperature well.
(2)每次測完要清潔塗杯，選用所測塗料相應的溶劑，防止測定小孔被堵。
(2) Clean the cup after each test, and select the appropriate solvent to prevent the test hole from being blocked.
(3)先用手指或器具堵嚴小孔漏嘴，倒滿100ml塗料，用玻璃棒將氣泡和多餘試樣倒入凹槽，防止測試樣本不夠或超過標準。
(3) Firstly, close the small hole and leak with finger or instrument, pour 100 ml paint, and pour bubbles and excess samples into the groove with glass rod to prevent the test samples from being insufficient or exceeding the standard.
(4)迅速移開手指時，同時啟動秒表，待試樣流速剛中斷時立即停止秒表，開始計時。
(4) When the finger is moved quickly, the stopwatch is started at the same time. When the sample flow rate is interrupted, the stopwatch is stopped immediately and the time is started.
以上是环氧地坪塗料黏度測試方法，而經常接觸环氧地坪塗料人員用經驗就可以檢測，其方法是：环氧地坪漆材料經攪拌後，用棒挑起塗料進行觀察便可（正常的塗料應自由降落而不斷，如有中斷而回縮現象，說明該塗料較稠），一般棒上的塗料與桶內塗料在很短時間內會連接不斷的流淌，連接距離為30-50cm，這時就是可以刷塗的程度；而小於30cm，就表明塗料的黏度太小，塗料太稀不宜塗刷；大於50cm，表明黏度太大，塗料太稠也不可直接施工。通過觀察檢測地坪漆塗料黏度，也可觀察塗料貯存一段時間後的聚合度，以按照不同施工要求，用適合的稀釋劑去調整黏度，從而達到环氧地坪漆施工所需的黏度指標。
Above is the test method for the viscosity of epoxy floor paint, which can be tested by the experience of people who often contact with epoxy floor paint. The method is that after mixing, the epoxy floor paint material can be observed by using stick to pick up the paint (normal paint should fall freely and continuously, if there is interruption and shrinkage phenomenon, indicating that the paint is thicker). Generally, the coatings on the rod and the coatings in the barrel are very short. In time, the continuous flow will be透水地坪 connected, the connection distance is 30-50 cm, which is the degree of brushing; and less than 30 cm, it shows that the viscosity of the paint is too small, the paint is too sparse to be brushed; more than 50 cm, indicating that the viscosity is too high, the paint is too thick to be directly applied.印花地坪 By observing and testing the viscosity of the floor paint, the degree of polymerization of the paint after storage for a period of time can also be observed to adjust the viscosity with suitable diluent according to different construction requirements, so as to achieve the required viscosity index for the construction of epoxy floor paint.