燃氣熱風爐運行人員有哪些調節檢測功能

燃氣熱風爐在啟動，運行的時候，需要根據當時的狀況進行調節。燃氣熱風爐運行人員都要根據相應的情況，對應怎樣的步驟都要有豐富的經驗。往往熱風爐運行時出現瞭異常情況都要馬上對燃氣熱風爐進行調節。這樣及時處理後才能保證熱風爐的運行安全。1.燃氣熱風爐的水壓力測試：在燃氣熱風爐壓力表安裝在熱風爐表面。壓力變送器集成裝置的調節，能改變熱風爐的壓力數值。壓力控制器可以控制顯示壓力的變化。水壓力變高時,燃氣熱風爐報警。當水壓力低於設定限制,這表明熱風爐缺水,熱風爐開始報警。
When the gas hot blast stove starts and runs, it needs to be adjusted according to the situation at that time. The operators of gas hot blast stoves should have rich experience in the corresponding steps according to the corresponding situation. Often, when the hot blast stove is running abnormally, it is necessary to adjust the gas hot blast stove immediately. In this way, the operation safety of hot blast stove can be guaranteed only after timely treatment. 1. Water pressure test of gas hot-blast stove: The pressure gauge of gas hot-blast stove is installed on the surface of hot-blast stove. The adjustment of pressure transmitter integrated device can change the pressure value of hot blast stove. Pressure controller can control the change of display pressure. When the water pressure increases, the gas hot blast stove alarms. When the water pressure is below the set limit, this indicates that the hot stove is short of water, and the hot stove starts to alarm. 2.燃氣熱風爐的煙氣溫度傳感器
2. Flue Gas Temperature Sensor for Gas Hot Blast透水地坪 Furnace
在燃氣熱風爐控制煙氣溫度的控制調節上，當煙氣溫度超過超過設定值時,熱風爐報警,顯示當時爐內的煙氣溫度。
When the flue gas temperature exceeds the set value, the hot air stove alarms to show the flue gas temperature in the stove at that time.
3.燃氣熱風爐返回水包熱電阻溫度傳感器
3. Thermal Resistance Temperature Sensor for Gas Hot Blast Furnace Return Water Ladle
在數控顯示器上顯示溫度。當水溫低於設定限制,熱風爐自動加熱直到熱風爐自動停止。如超過最大限度值超溫報警停爐。返回水溫由於环境溫度的變化,當回歸水的溫度變高,燃燒的火焰自動變小;當回歸水的溫度變低,燃燒火焰自動變大。
Display the temperature on the NC display. When the water temperature is below the set limit, the hot stove is heated automatically until the hot stove stops automatically. If the max彩色沥清地坪imum value is exceeded, the boiler will be stopped by alarm. Because of the change of ambient temperature, when the temperature of return water increases, the flame of combustion automatically decreases; when the temperature of return water decreases, the flame of combustion automatically increases.
4.燃氣熱風爐氣壓計氣體壓力開關
4. Gas Pressure Switch of Gas Hot Stove Barometer
調節壓力開關可以改變熱風爐的壓力大小。對熱風爐使用超低氣壓保護，如果氣體泄漏，顯示器會顯示異常。
The pressure of hot stove can be changed by adjusting pressure switch. Ultra-low pressure protection is used for hot stove. If the gas leaks, the monitor will show abnormal.
5.燃氣熱風爐氣體泄漏檢測設備
5. Gas Leakage Detection Equipment for Gas Hot Blast Furnace
燃氣熱風爐氣體泄漏檢測設備可以讓煤氣泄漏時自動停止供氣，並且熱風爐進行燈光報警。
Gas leakage detection equipment of gas hot stove can automatically stop gas supply when gas leakage occurs, and the hot stove can alarm by light.