燃氣熱風爐產品都有相應確切的專項安全檢測標

燃氣熱風爐與其它燃氣具不一樣，它的設備方位特別，耗氣量大，是安全性要求較高的商品。所以，所有燃氣壁爐商品在推向市場之前都必須經過嚴格的安全环保規范檢查。檢查規范也跟著商品的開展而不斷更新。各類熱風爐商品都有相應切當的專項安全檢查規范。代表瞭商品的安全环保已到達規范，用戶可放心運用。
Gas hot blast stove is different from other gas appliances because of its special equipment orientation and large gas consumption. It is a commodity with high safety requirements. Therefore, all gas fireplace commodities must undergo strict safety and environmental protection standards inspection before they are put into the market. Inspection specifications are constantly updated with the development of commodities. All kinds of hot-blast stove commodities have appropriate special safety inspection specifications. Represents the safety and environmental protection of commodities has reached the norms, users can rest assured that the use.
采購燃氣壁掛熱風爐首先要，應依據房子面積巨細，一般每平米需求的供熱功率大約在120w－180w之間。因而，當你挑選采熱風爐前，應先尋求服務商的定見，這個要看在哪個城市，房子的保溫狀況來決議。然後測算一個大致的整體功率。引薦一個核算大致功率的公式：房子的建築面積×65％×150w。一般采暖面積會在建築面積的60％－70％之間，假如是一套150平方米的公寓房，它的采暖面積大概在90－105平方米之間。
The first step in purchasing gas wall-mounted hot-blast stoves should be based on the size of the house. The heating power required per square meter is generally between 120W and 180w. Therefore, before you choose the stove, you should first seek the opinion of the service provider, which depends on the city and the insulation of the house. Then calculate a roughly total power. A formula for calculating approximate power is introduced: the building area of the house is *65%*150w. General heating area will be between 60% and 70% of the building area. If it is a 150 square meters apartment, its heating area will be between 90 and 105 square meters.
小區運用燃氣熱風爐，常見於獨立的單位宿舍，房地產開發商運用的並不多。進口燃氣熱風爐顯著報價高，國產的又存在運用壽命、熱效率等疑問。即使運用國產較好的熱風爐，與壁掛爐相比其實踐出資也是不低的。水源熱泵的一次性出資依據工程商的狀況，或高或低，但相同存在著辦理特別收費難的疑問，且該技能在中國還有許多當地需求不斷完善。
Gas-fired hot stoves are commonly used in residential quarters, but few are used by real estate developers. The imported gas hot blast stove has a remarkable high quotation, while the domestic gas hot blast stove has some doubts about its service life and thermal efficiency. Even if better domestic hot stoves are used, their practical investment is not low compared with wall-mounted stoves. The one-time investment of water source heat pump is based on the condition of the engineers, high or low, but there is the same question that it is difficult to handle special fees, and there are many local needs to improve this skill in China.
咱們在平時運用燃氣熱風爐時呈現回火脫火主要是因為焚燒時有必定的速度，空氣中的濃度處於焚燒極限濃度范圍內，可燃氣體的流速低於焚燒速度時就會發作回火，爐溫越高火焰速度越快就簡單發作回火，假如呈現回火會把焚燒器燒壞，嚴峻時還會發作爆破。
When we use gas hot blast stove in peacetime, tempering takes place mainly because there is a certain speed when burning. The concentration of air is within the limit concentration range of burning. When the flow rate of combustible gas is lower than the burning speed, tempering will occur. The higher the temperature of the stove, the faster the flame speed, the easier the tempering will occur. If tempering takes place, the tempering wil彩色沥清地坪l occur. The incinerator burns out and bursts in severe cases.
假如氣體在焚燒器出口的流速高於焚燒速度時會發作脫火。爐溫越低越簡單發作脫火，會使焚燒不穩定也許導致熄火。燃料的速度是由壓力決議的，管道壓力俄然改變會使燃氣壓力忽高忽低，及風量調理不妥也許形成焚燒器出口氣流的不穩定，會形成回火或許脫火。
If the gas flow rate at the exit of the incinerator is higher than that of the incinerator, the ignition will occur. The lower the furnace temperature, the simpler the ignition will occur, which will make the combustion unstable and may lead to extinction. Fuel speed is determined by pressure. Sudden change of pipeline pressure will cause gas pressure to rise or fall, and improper air conditioning may result in unstable flow at the burner outlet, tempering or fire-off.
選用原裝進口焚燒器，全主動程序化操控，風機主動吹掃，電子主動焚燒，油氣主動焚燒，風油（氣）主動份額調理，霧化效果好，焚燒充沛，節能环保，擁有熄火保護設備確保焚燒安全。在正常狀況下，焚燒器出力隨熱風爐溫度而主動調整焚燒火苗長度，熱風爐出口溫度到達設定值時，焚燒器主動中止焚燒，當溫度低於設定值時，焚燒器主動開端作業。當發作燃料、進風反常等景象時，毛病燈亮，程控設備會馬上中止輸出燃料，焚燒機主動停機。
The original imported incinerator is selected, which is fully procedural operation, active blower sweeping, electronic active incine印花地坪ration, active oil and gas incineration, active air-oil (gas) share conditioning, good atomization effect, abundant incineration, energy saving and environmental protection, and fire extinguishing protection equipment to ensure the safety of incineration. Under normal conditions, the burner output actively adjusts the burning flame length with the temperature of the hot blast stove. When the outlet temperature of the hot blast stove reaches the set value, the burner actively stops burning. When the temperature is lower than the set value, the burner actively starts operation. When the scene of fuel and abnormal air intake occurs, the faulty lamp lights up, the program-controlled equipment will immediately stop the output of fuel, and the incinerator will stop on its own initiative.