翅片管是如何按應用場合進行分類的？

翅片管是如何按應用場合進行分類的？翅片管的種類很多，而且還在不斷湧現新的品種。翅片管大體上在應用場合可按下述幾個方面進行分類：翅片管在幹燥設備的運行中的作用是給熱空氣加熱物料，這樣就使得物料中的水分會蒸發，然後在進行循环幹燥的時候，因為存在著較高的溫度的空氣已經接近瞭飽和狀態，所以翅片管中高溫高濕的空氣已經不能將物料中的水分帶走，所以材料中的水分開始停止蒸發，繼續操作會對其產生不利的影響，需要排除這種做法。How do the finned tubes be classified by application? There are many kinds of finned tubes, and new varieties are emerging. In general, finned tubes can be classified into the following categories in application: the function of finned tubes in the operation of drying equipment is to heat materials for hot air, so that the moisture in materials will evaporate, and then in the process of cyclic drying, because the air with higher temperature is close to saturation state. Therefore, the high temperature and humid air in the finned tube can no longer take away the moisture in the material, so the moisture in the material begins to stop evaporating, and continuing to operate will have adverse effects on it, which needs to be eliminated. 在一般的情況下，如果是材料的含水量較高的話，就會在很短的時間內就會造成外界熱空氣的較為飽和的狀態，如果一般都采用的全新風進行幹燥，就是指翅片管的翅片管在進行加熱之後，把達到溫度的熱空氣在送進幹燥器裡，同時再→另外一段排出，在隧道式烘道內，熱空氣的流向與物料的流量相逆流。In general, if the moisture content of the material is high, it will cause a relatively saturated state of the hot air outside in a very short time. If the fresh air is generally used for drying, it means that the finned tube of the finned tube is heated and the hot air that reaches the temperature is fed into the dryer. At the same time another section is discharged. In the tunnel drying channel, the flow direction of hot air is countercurrent to the flow rate of material.還有一種情況就是進行熱風循环幹燥，因為材料中的含水量不高，所以在較短的時間裡不容透水地坪易對熱空氣造成飽和，但是如果幹燥的話條件又需要保持一定的蒸發溫度條件，此時，多采用排除部分濕熱空氣，補充部分新風，節約能源消耗，降低生產成本。新風的補充量一般為20-30%不等，具體需視工藝要求而定。Another case is hot air cycle drying, because the moisture content in the material is not high, so it is not easy to saturate the hot air in a short time, but if the drying conditions need to maintain a certain evaporation temperature conditions, at this time, more use to exclude part of the hot and humid air, supplement part of the fresh air, saving. Energy consumption, reduce production costs. The replenishment of fresh air is generally 20-30%, depending on the technological requirements.翅片管按加工工藝分類：Finned tubes are classified according to processing technology.1.串片管（套片管）；1. series tube (sleeve tube);2.張力纏繞翅片管；2. tension winding fin tube;3.鑲片管；3. insert tube;4.整體軋制翅片管；4. integral rolling fin tube;5.鑄造翅片管；5. casting finned tube;6.焊接翅片管，其中又分：高頻焊翅片管，埋弧焊翅片管，等。6. welding finned tubes, which are divided into high frequency welding finned tubes, submerged arc welding finned tubes, etc.按翅片形狀分類：Classification by fin shape:1.方形，矩形，圓形翅片管；1. square, rectangular and circular finned tubes.2.螺旋形翅片管；2. spiral finned tube;3.波紋形翅片管；3. corrugated finned tube;4.鋸齒形翅片管；4. saw tooth finned tube;5.針狀翅片管；5. needle fin tube;6.縱向翅片管；6. longitudinal fin tube;7.整體板狀翅片管（板翅）等。7. integral plate fin tube (plate fin) and so on.翅片管按材質分類Finned tubes are classified according to material quality.1.銅，Al, Cu/Al翅片管；1. copper, Al, Cu/Al finned tubes;2彩色沥清地坪.碳鋼，不銹鋼，碳鋼/不銹鋼翅片管；2. carbon steel, stainless steel, carbon steel / stainless steel finned tube;3.鑄鐵(鑄鋼）翅片管；等。3. cast iron (cast steel) finned tube, etc.翅片管按用途分類：Finned tubes are classified according to their usage:空調用翅片管；Finned tube for air conditioner;空冷用翅片管；Finned tube for air cooling;鍋爐：水冷壁，省煤器，空預器分別使用的翅片管；Boiler: finned tube used for water wall, economizer and air preheater.各種窯爐，工業爐餘熱回收用翅片管；Finned tubes for waste heat recovery of various kilns and industrial furnaces;其他特種用途翅片管；等。