环氧地坪漆施工方法及註意事項

环氧地坪漆在施工過程中，擁有先進的基面處理設備、塗裝施工工具及質量控制儀器是創造優良环氧地坪漆工程的有力武器。环氧地坪漆，环氧地坪塗料常用施工工具與設備，據介紹，主要包括以下幾個方面：
In the construction process of epoxy floor paint, it is a powerful weapon to create excellent floor paint projects with advanced base treatment equipment, painting construction tools and quality control instruments. Epoxy floor paint, common construction tools and equipment of epoxy floor paint, according to the introduction, mainly includes the following aspects:
施工步驟：
Construction steps:
1.素地處理
1. prime processing
①基礎素地以水泥粉光面或磨石地為準；
(1) based on cement powder or grindstone,
②素地需養生28天以上，水份需8%以下方可施工素地如有不平或空鼓需加以除去；
(2) The vegetable land should be kept in good health for more than 28 days, and the water content should be less than 8% before it can be removed if there is unevenness or empty drum in the construction of the vegetable land.
③用环氧砂漿補平地面；
Third, use epoxy mortar to patch the ground.
④素地之油污需澈底清洗幹凈；
4. The oil pollution of prime land must be cleaned thoroughly.
⑤施工前需保持施工素地之幹燥和清潔；
Before construction, it is necessary to keep the construction site dry and clean.
2.底塗層
2. bottom coating
①施工前需保持幹凈如有雜物粘附需清除依照正確比例將主劑及硬化劑混合，充分攪拌；
1. Keep clean before construction. If there is any debris adhesion, remove the main agent and hardening agent according to the correct proportion and mix them fully.
②需視地面情況調整適當粘度混合完成材料需4小時以內施工完成；
Second, it is necessary to adjust the proper viscosity and finish the material within 4 hours according to the ground conditions.
③底塗層養生硬化時間約8小時以上。
3. The curing time of the bottom coating is about 8 hours.
3.中塗層
3. medium coating
①施工前需要保持幹凈如有雜物粘附需清除依照正確 比例將主劑及硬化劑混合，充分攪拌；
(1) Before construction, it is necessary to keep clean. If debris adheres, it is necessary to remove and mix the main agent and hardening agent according to the correct proportion and mix them fully.
②將混合完成的樹脂適量加入石英砂；
(2) adding proper amount of resin to the quartz sand.
③使用鏝刀將材料均勻塗佈；
3. Use the trowel to evenly coat the material.
④混合完成材料需30分鐘以內施工完成；
(4) the mixture should be completed within 30 minutes.
⑤施工交接處做好交接處理；
(5) handle the handover at the construction junction.
⑥中塗層養生硬化時間約8小時以上。
The curing time of middle coating is about 8 hours.
4.批土層
4. batches of soil
①依照正確比例將主劑及硬化劑混合，充分攪拌；
1. Mix the main agent and hardener in proper proportion and stir well.
②使用批刀將材料塗佈均勻；
Second, use the batch knife to coat the material evenly.
③混合完成材料需30分鐘內施工完成；
(3) the mixture will be completed in 30 minutes.
④批土養生硬化時間約8小時以上；
(4) soil curing time is more than 8 hours.
⑤視實際需要施工數道要求達到平整無孔洞，無批刀印及砂磨印為準。
(5) according to the actual needs, the construction requirements of the construction must be smooth and no holes, and no batch cutter and sand print shall prevail.
5.面塗層
5. surface coating
①施工前需保持幹凈如有雜物粘附需清除；
1. Keep clean before construction;
②使用前主劑先攪拌均勻；
The main agent should be mixed before use.
③依照正確比例將主劑及硬化劑混合，充分攪拌；
Third, mix the main agent and hardener in the right proportion and stir well.
④使用滾筒或鏝刀將材料均勻塗佈混合完成材料需30分鐘以內施工完成；
(4) use the roller or trowel to evenly coat the material and complete the material in 30 minutes.
⑤施工交接處需做好交接處理；
(5) the handover should be done well at the construction junction.
⑥施工完成後，24小時後方可上人，72小時後方可重壓（以250C為準，低溫時開放時間需適度延長）
_After the completion of construction, people can enter the building 24 hours later, and heavy pressure can be applied 72 hours later (based on 250C, the opening time should be prolonged at low temperature). 环氧地坪漆，环氧地坪塗料常用施工工具與設備
Epoxy floor paint, commonly used construction tools and equipment for epoxy floor coatings
环氧地坪漆是采用無溶劑優質环氧樹脂及固化劑配置而成。表面平滑、美觀、達鏡面效果，具有耐較強酸、堿、鹽、油類介質腐蝕，耐強堿性特優，耐磨、耐壓、耐沖擊，潔凈程度較高等特點。適用於高度清潔、美觀、無塵、無菌的電子、微電子行業，實行GMP標準的制藥、血液制品行業，也可用於學校、辦公室、傢庭等环氧地坪。
Epoxy floor paint is made of solventless high quality epoxy resin and curing agent. Smooth, beautiful, mirror effect, with strong acid, alkali, salt, oil medium corrosion resistance, strong alkali resistance, excellent wear resistance, pressure resistance, impact resistance, high cleanliness and so on. It is suitable for highly clean, beautiful, dust-free, sterile electronics and microelectronics industries, pharmaceuticals and blood products industries that implement GMP standards, as well as floors of schools, offices and families.


一、基面處理設備
1. Base surface processing equipment
1、磨削機：裝配金剛研磨刀，用於混凝土、水磨石、硬化耐磨地面、大理石等基材表面打磨處理。
1. Grinding machine: assemble diamond grinding tool for grinding concrete, terrazzo, hardened wear-resistant ground, marble and other base materials.
2、便攜式磨削機：用於小面積混凝土、水磨石、硬化耐磨地面、大理石等基材表面或邊角部位打磨處理，亦可用於去除小面積的舊漆和油污層。
2. Portable grinder: It is used for grinding small area of concrete, terrazzo, hardened wear-resistant ground, marble and other base material surfaces or corners. It can also be used to remove small areas of old paint and paint layer.
3、銑刨機：用於銑刨去除舊漆層、油污層等。
3, milling machine: for milling, remove old paint layer, oil pollution layer.
4、拋丸設備：用於大面積混凝土、水磨石、硬化耐磨地面、大理石等基材表面拋丸處理。
4. Shot blasting equipment: used for large area of concrete, terrazzo, hardened wear-resistant ground, marble and other base material surface shot blasting treatment.
5、吸塵器：去除地面灰塵。
5. Vacuum cleaner: remove dust from the ground.

二、塗裝施工工具
Two. Coating construction tools
1、鋸齒鏝刀、釘鞋、釘子輥筒：鋸齒鏝刀用於鏝塗自流平地坪塗料，然後用釘子輥筒輥壓以釋出膜內空氣，對於局部塗裝缺陷可在塗膜表幹前穿釘鞋前往修復。
1. Sawtooth trowel, nail shoe, nail roll彩色沥清地坪er: Sawtooth trowel is used for trowelling self-leveling floor paint, and then the air inside the film is released by roller pressing with nail. For local coating defects, the nail shoe can be worn to repair before the film surface is dry.
2、平底刮板：用於刮塗底漆、砂漿、膩子等稠厚地坪塗料，適合於緊貼地面刮塗。
2. Flat-bottomed scraper: It is used for scraping thick floor coatings such as primer, mortar, putty, etc. It is suitable for scraping close to the ground.
3、輥筒與漆刷：質量優異、不掉毛的輥筒和刷子方能獲得良好的外觀，通常短毛輥筒具有更好的操作性。
3. Rollers and brushes: Excellent quality, non-hair loss roller and brush can get a good appearance, usually short hair roller has better operability.
4、無空氣噴塗機：用於噴塗施工地坪面漆，效率高，易獲得良好的裝飾效果，易控制塗料耗量；須根據塗料粘度及使用期選擇噴泵和噴咀，以獲得適合的流體壓力和流量。通常電驅動或內燃機驅動的高壓無氣噴塗機因其良好的便攜性而得到廣泛應用。
4. Air-free spraying machine: It is used for spraying floor topcoat, with high efficiency, easy to obtain good decorative effect and easy to control paint consumption; spraying pump and nozzle should be selected according to paint viscosity and service life in order to obtain suitable fluid pressure and flow rate. Usually high-pressure airless spraying machine driven by electric or internal combustion engine is widely used because of its good portability.
5、空氣噴塗設備：包括空氣壓縮機和空氣噴槍，可用於噴塗施工低粘度的地坪塗料。
5. Air spraying equipment: including air compressor and air spraying gun, which can be used for spraying low-viscosity floor coatings.
6、砂漿攪拌機、鋪料器與抹光機：用於施工厚層(≥3mm)樹脂砂漿，將攪拌均勻的樹脂砂漿用鋪料器攤鋪於地板上，采用抹光機抹平。
6. Mortar mixer, paver and polisher: used for construction of thick layer (> 3mm) resin mortar. The evenly mixed resin mortar is spread on the floor with paver and polished with polisher.
7、消泡滾筒刷：適用於地坪漆施工，可消除氣泡，滾平效果好。
7, defoaming drum brush: applicable to floor paint construction, can eliminate bubbles, roll leveling effect is good.
8、地坪漆平口、圓口鏝刀：采用錳鋼材料制造，適用於地坪漆、环氧地坪漆施工。
8. Floor paint flat mouth, round mouth trowel: Made of manganese steel, suitable for floor paint, epoxy floor paint construction.

三、中塗打磨設備
Three. Medium grinding equipment
1、大打磨機：高效快速的中塗層打磨設備。
1, large grinding machine: efficient and fast medium coating grinding equipment.
2、拋光機與砂帶機：配以80～120目的磨片及砂帶，在塗裝面漆前打磨砂漿或膩子層以獲得平整細膩的表面；配以較粗(20～40目)的磨片及砂帶亦可以用於混凝土等基材表面的簡易打磨處理。
2. Polishing machine and abrasive belt machine: with 80-120 mesh abrasive discs and belts, we can polish the mortar or putty layer before finishing paint to obtain a smooth and delicate surface; with coarse (20-40 mesh) abrasive discs and belts, we can also use them for simple polishing of the surface of concrete and other substrates.

四、檢驗與試驗設備
Four. Testing and testing equipment
1、底材表面溫度及环境溫濕度儀：測定塗裝环境溫濕度及底材表面溫度以確定是否滿足塗裝要求。
1. Substrate Surface Temperature and Ambient Temperature and Humidity Meter: Determine the ambient temperature and humidity of the coating and the surface temperature of the substrate to determine whether it meets the coating requirements.
2、基材含水率測定儀：用以測定基材含水率以判定是否符合塗裝要求。
2透水地坪. Substrate moisture content tester: used to determine the moisture content of the substrate to determine whether it meets the coating requirements.
3、導靜電電阻測定儀：用以測定防靜電地坪的導靜電電阻率。
3, conductive electrostatic resistance tester: used to measure electrostatic conductivity of anti-static floor. 五、其它輔助工具
Five. Other auxiliary tools.
1、切縫機與打膠槍：用於縫隙的處理，切割機用於將縫隙切割和修飾成“V”字形或梯形(寬5-10mm)以方便填補和灌註；而打膠槍用於灌註聚氨酯彈性膠。
1. Sewing machine and glue gun: for the treatment of cracks, the cutting machine is used to cut and modify the cracks into V-shaped or trapezoidal (5-10mm wide) for easy filling and filling; and the glue gun is used for filling polyurethane elastomer.
2、稱量與攪拌工具：較高精度的稱量工具有利於按比例準確配制多組份地坪塗料，使用電動攪拌器充分快速地混合和攪拌塗
2. Weighing and mixing tools: Higher precision weighing tools are conducive to the accurate preparation of multi-component floor coatings in proportion, and the use of electric agitators to mix and mix sufficiently and quickly.