分析环氧樹脂耐磨地坪漆常見質量問題

环氧樹脂耐磨地坪漆有著防腐蝕、耐磨損、防滑、污染小及裝飾性強等特點，在工業环氧地坪及环境要求場所所得到瞭大量采用，由於施工質量和环境因素的影響導致產生一些質量問題，下面就环氧樹脂耐磨地坪漆常見問題做個分析：在選購环氧地坪漆商傢尤為重要，市場上呈現大量劣質环氧地坪漆生產廠傢，施工技術不到位，都是導致以上問題出現的源頭。
Epoxy resin wear-resistant floor paint has the characteristics of corrosion resistance, wear resistance, skid resistance, small pollution and strong decoration. It has been widely used in industrial epoxy floor and environmental requirements places.彩色沥清地坪 Due to the influence of construction quality and environmental factors, some quality problems have arisen. Here are some common problems of epoxy resin wear-resistant floor paint. An analysis: It is particularly important to select and purchase epoxy floor paint manufacturers. A large number of inferior epoxy floor paint manufacturers and inadequate construction technology are the sources of the above problems. 1、滲色問題
1. The problem of colouring.
滲色是指當一種顏色底漆塗膜上覆蓋另一種顏色的面漆時，會讓表面塗膜出現變色的情況，主要原因有以下幾點：底漆並沒有完全幹燥、底漆和面漆顏色上有色差、漆中含有雜色物質。
Colouring refers to the discoloration of the surface coating when one color primer is coated with another color. The main reasons are as follows: the primer is not completely dry, the color of the primer and the top coat is different, and the paint contains impurities.
2、漆面較花
2. The paint is more beautiful.
是指塗膜表面色彩不夠均勻，有斑紋及顏色雜亂的現象，原因是由於施工過程中，塗臉的配料不當及塗抹不均勻所致。
It refers to the phenomenon that the color of the coating surface is not un环氧地坪iform enough, there are spots and disorderly colors. The reason is due to improper ingredients and uneven application during the construction process.
3、表面泛白
3. Surface whitening
是指施工作業完成後，地表塗層的塗抹出現泛白現象，原因有幾點：空氣中的濕度過高、塗面幹燥過程使用瞭過多的快幹劑。
It refers to the whitening phenomenon of surface coating after the completion of construction work. There are several reasons: excessive humidity in the air, excessive use of quick drying agent in the drying process of coating surface.
4、起皺、針眼、魚眼
4. Wrinkle, needle eye, fish eye.
塗膜表層出現起皺現象，主要原因是漆面內外層幹燥速度不一致造成表層收攏起皮、針眼是因為溶劑發揮太快，漆液補充不及時造成的、魚眼是因為塗料或外界的雜質混入造成塗料附著力不均勻。
The wrinkling phenomena on the surface of coatings are mainly caused by the inconsistency of drying speed between the inner and outer layers of the coatings, which results in the folding up of the surface and pinholes because the solvent is exerted too fast, the filling of the paint is not timely, and the fisheye is due to the uneven adhesion of the coatings caused by the mixing of paint or external impurities.
5、粗糙、開裂問題
5. Rough and cracked problems
粗糙現象是指表層有大小不同的顆粒狀物質出現，主要原因是塗料中含有不易溶解的雜質及外界灰塵所致。地表開裂現象是因為原材料和施工質量問題，導致漆層附著力下降，在外界作用力影響下，出現掉皮開裂現象。
Roughness refers to the appearance of granular substances of different sizes on the surface. The main reason is that the coating contains insoluble impurities and external dust. Surface cracking is caused by quality problems of raw materials and construction, which leads to the decrease of adhesion of paint layer. Under the influence of external forces, skin cracking occurs.