翅片管散熱器的生產及選購參數

關於生產技術1 ：鋼制翅片管對流散熱器應按批準的產品圖樣及技術文件制造，並應符合本標準的規定。2 ：鋼制翅片管對流散熱器外罩帶後背板、聯箱內藏。鋼帶、外罩板和兩端護板應符合有關材料標準的規定，並且應具有材料質量合格證明書。3：鋼管橢圓度應不大於0. 3 mm,鋼管其他項目應符合GB/T 3092,GB/T 3087,GB/T 8163的規定。4 ：鋼帶與鋼管之間應采用高頻焊或其他確保緊固的方法。JG/'r 3012. 2一1998About production technology 1: Steel finned tube convection radiator shall be manufactured according to approved product drawings and technical documents, and shall comply with the provisions of this standard. 2: steel finned tube convection radiator cover with back plate, joint box inside. The steel strip, cover plate and both ends guard plate shall conform to the relevant material standards and shall have a certificate of material quality. 3: The ovality of steel pipe should not exceed 0.3 mm. Other items of steel pipe should conform to the stipulations of GB/T 3092, GB/T 3087 and GB/T 8163. 彩色沥清地坪4: high frequency welding or other ways to ensure fastening should be adopted between steel strip and steel pipe. JG/'r 3012.2 1 19985 ：鋼帶、鋼管的焊接表面應無塗層、鐵銹、凹坑等影響焊接質量的缺陷和雜質。5: The welding surface of steel strip and steel pipe should be free of defects and impurities such as coating, rust and pits which affect the welding quality.6：翅片管質量要求翅片管螺距6-7 mm，翅片高度應大於15 mm，翅片傾伏角不應大於80,翅片管的直線度每米不應大於1.0 m m. 對於采用高頻焊接工藝的翅片管，每米翅片管測量處實際焊縫長度的總和應大於85 ，且未連續焊接長度不應大於50 mm.6: Finned tube quality requirements finned tube pitch 6-7 m m, fin height should be greater than 15 m m, fin dip angle should not be greater than 80, finned tube straightness should not be greater than 1.0 M. For finned tube using high-frequency welding process, the total length of the actual weld at the finned tube measurement should be greater than 85, and the length of non-continuous welding should not be greater than 80. More than 50 mm.7 ：鋼制翅片管對流散熱器焊接質量要求: 鋼管與鋼管的對接應符合GB 151的規定。焊接應符合GB/T 985的規定。7: Steel finned tube convection radiator welding quality requirements: steel pipe and steel pipe butt should comply with the requirements of GB 151. Welding shall comply with the requirements of GB/T 985.8 ：鋼制翅片管對流散熱器在加外罩前應逐組進行水壓試驗或氣壓試驗，試驗壓力為工作壓力的1.5倍。8: Steel finned tube convective radiator shall be tested by water pressure or air pressure one by one before adding cover. The test pressure is 1.5 times of working pressure.9 ：鋼制翅片管對流散熱器接管螺紋應符合JG .1 31的規定。9: steel finned tube convection radiator pipe thread should comply with the requirements of JG.1 31.10 ：漆膜質量要求鋼制翅片管對流散熱器應噴塗防銹底漆和面漆;面板應烤漆，漆膜的制備應符合GB/T 1727的規定。表面塗層應均勻光滑，附著牢固，不得有氣泡、堆積、流淌和漏噴。10: Coating film quality requirements of steel finned tube convection radiator should be sprayed with anti-rust primer and topcoat; panel should be baked paint, paint film preparation should comply with GB / T 1727 requirements. The surface coating should be uniform and smooth with firm adherent. No bubbles, stacking, flowing and leaky spray should be allowed.翅片管finned tube關於選購About buying and buying如何選擇翅片管散熱器確實是消費者需要好好思考的一個問題。How to choose finned tube radiator is a problem that consumers need to think about carefully.有些註重熱效率，關心是否能在短時間內獲得明顯的效果；有些則因环境因素，側重是否耐腐蝕；還有在意外形是否美觀。如此種種。那麼哪些是最基本的、不可忽視的呢？Some pay attention to thermal efficiency, concerned about whether in a short period of time to achieve significant results; some are due to environmental factors, focusing on whether corrosion resistance; and whether the unexpected appearance is beautiful. So many. So what are the most basic and important things to ignore?第一：翅片管散熱器的工作壓力，應滿足系統的工作壓力，並符合國傢現行有關產品標準的規定；Firstly, the working pressure of finned tube radiator should satisfy the working pressure of the system, and conform to the relevant national product standards.第二：放散粉塵或防塵要求較高的工業建築，應采用易於清掃的翅片管散熱器；Secondly, finned tube radiators should be used in industrial buildings where dust emission or dust prevention is required.第三：具有腐蝕性氣體的工業建築或相對濕度較大的使用环境下，應采用耐腐蝕的翅片管散熱器；Thirdly, corrosion-resistant finned tube radiators should be used in industrial buildings with corrosive gases or in high relative humidity environment.第四：采用鋼制翅片管散熱器時，應采用閉式系統，並滿足產品對水質的要求Fourth: the use of steel finned tube radiator, should be closed system, and meet the product requirements for water quality第五：采用鋁制翅片管散熱器時，應選用內防腐型鋁制翅片管散熱器，並滿足產品對水質的要求；Fifth: the use of aluminum finned tube radiator, should choose internal corrosion-resistant aluminum finned tube radiator, and meet the product requirements for water quality;第六：選擇正規的翅片管散熱器生產廠傢，具有更好的售後指導安裝，技術支持，我公司專業制造各類散熱器設備、換熱器、油冷卻器、表面空氣冷卻器、暖氣片、翅片管,產品通過上海同濟大學,中國紡織大學檢測，達到先進水平, 歡迎新老客戶來電咨詢,詢盤,我們真誠與您合作!Sixth: Select the regular finned tube radiator manufacturer, with better after-sales guidance installation, technical support, our company specializes in manufacturing all kinds of radiator equipment, heat exchangers, oil coolers, surface air coolers, heating fins, finned tubes, products through Shanghai Tongji University, China Textile University testing, to achieve advanced water Ping, welcome new and old customers to inquire, inquiry, we透水地坪 sincerely cooperate with you!辛苦整理.轉載請註明http://www.wxsxsjx.com