廠傢揭示环氧地坪怎樣施工呢？施工步驟

下面為大傢介紹环氧地坪施工步驟：一、基礎處理1、用研磨機進行全面打磨。讓破損、起沙、粘度不牢、開裂、空鼓之部位完全暴露出來；並將浮起的砂漿、舊环氧地坪水泥結塊等打磨平整。2、有松動、裂縫或脫層的地面，必須徹底打磨至密實基層，保證地面的粘結度3、將基層表面的浮灰、污染物等垃圾清理幹凈，確保基層表面的幹凈度。4、將處理過的地面清潔。
Following is an introduction to the construction steps of epoxy floor: 1. Foundation treatment 1. Comprehensive grinding with a grinder. Let the damaged, sand-lifting, weak viscosity, cracking, empty drum parts completely exposed; and the floating mortar, old epoxy cement caking and other grinding flat. 2. Grounds with loose, cracked or delaminated surfaces must be thoroughly polished to a compact base, ensuring the cohesion of the ground 3, cleaning up the floating ash and pollutants on the base surface, and ensuring the cleanliness of the base surface. 4. Clean the treated ground.
檢驗方法：經處理後，环氧地坪表面平整、密實、幹燥，無油污、且沒有松動易碎顆粒，方可進行下一工序施工。
Inspection method: After treatment, the floor surface is smooth, compact, dry, no oil pollution, and no loose and fragile particles, before the next process of construction can be carried out.
伸縮縫、裂縫、空鼓地面、松動舊环氧的特殊處理
Special treatment for expansion joints, cracks, hollowing floors and loose old epoxy
1、對開裂之部位采用切割片切成V型小槽後，再用高倍中塗砂漿予以修補填平；細小的裂縫可以用环氧樹脂加Extender T增稠劑修補；待完全固化後再用手磨機細打至平整。
1. Cutting slices into V-shaped grooves are used to repair and fill the cracks. Fine cracks can be repaired with epoxy resin and Extender T thickener. Fine cracks can be smoothed by hand grinder after solidification.
2、對空鼓、舊环氧松動之部位鑿除，如凹糟較深，采用高倍中塗砂漿予以補平，完全固化後再用手磨機細打至平整。
2. Cut hollow drum and loose parts of old epoxy, such as deep concave, use high-power medium-coated mortar to flatten them, and then grind them fine to flat after solidification.
3、所有特殊場地修補處理後，再清潔一遍。
3. All special sites should be cleaned once again after repair.
檢驗方法：
Methods of inspection:
a、以上部位的處理是整個环氧地坪使用壽命長短的重要一环，不然將導致地坪開裂。
A. The treatment of the a印花地坪bove parts is an important part of the whole service life of the floor, otherwise it will lead to cracking of the floor.
b、經處理後，與整個地面相平，修補處無離間、密實，堅硬，平整。
B, after processing, and the entire ground level, the repair place without separation, dense, hard, smooth.
二、环氧底塗
Two. Epoxy primer
1、施工前需確保地
1. Ensure construction before construction.
2、將环氧樹脂和固化劑按正確比例混合攪拌，
2. Mix the epoxy resin and the curing agent in the right proportion.
3、攪拌均勻後，采用刮刀或滾筒施塗的方法施塗。
3. After mixing evenly, apply scraper or roller.
环氧地坪4、要求浸透加強附作力。
4. It is required to soak and strengthen the attachment force.
5、待第一遍幹固後再施塗环氧中塗層。
5, after the first dry, the epoxy coating will be applied again.
三、环氧中塗層
Three. Epoxy coating
1、施工前需確保地面幹凈，如有雜物粘附需清除；
1. Before construction, make sure that the floor is clean.
2、將环氧樹脂和固化劑按正確比例混合攪拌，並按配比加上一定的石英砂；
2. Mix the epoxy resin and the curing agent in the right proportion and add a certain amount of quartz sand to the ratio.
3、攪拌均勻後傾倒在地面上，使用鏝刀按設計的厚度將材料均勻鏝開，以增加強度和耐沖擊力；使地面更加結實，抗壓。
3. After mixing evenly, dump it on the ground. Use trowel to evenly trowel the material according to the designed thickness, so as to increase the strength and impact resistance, and make the ground stronger and more compressive.
4、中塗層幹固後，采用打磨，把表面的流掛物、顆粒打磨平整。
4. After dry coating, the middle coating is ground and smoothed by grinding.
5、灰塵處理幹凈。
5, dust disposal is clean.
檢驗方法：施工交接處理是否妥當，踢腳線位置平直，與墻壁無離間，平整。
Inspection method: Whether the construction handover treatment is appropriate, the position of kick line is straight, no separation from the wall, flat.
四、环氧膩子層
Four, epoxy putty layer
1、在潔凈的地面上，將环氧樹脂和石英粉按正確的配比攪拌均勻後，采用批刀均勻鏝刮在地面上，以增加中塗與面層之間的結合，並進一步調整地面的平整度；
1. After mixing the epoxy resin and quartz powder in the right proportion on the clean ground, the batch knife is used to scrape evenly on the ground to increase the combination between the middle coating and the surface layer and further adjust the levelness of the ground.
2、視實際需要施工遍數，要求達到平整無孔洞，無批刀印及砂磨印為準。
2, depending on actual needs, the number of construction is required to achieve smooth, non hole, no batch knife printing and sand grinding.
檢驗方法：使地面完全平整無孔洞，無批刀印及砂磨印方可進行面塗層施工。
Inspection method: To make the ground completely flat without holes, no batch of knife prints and sanding prints before surface coating construction can be carried out.
五、环氧面塗層
Five. Epoxy coating
1、施工前需保持幹凈，如有雜物粘附需清除；
1, before construction should be kept clean.
2、將面塗材料的B組份先攪拌均勻；再加入固化劑混合，充分攪拌；
2. First, evenly mix the B components of the surface coating material; then add the curing agent and mix well and stir well.
3、使用輥筒將材料均勻塗佈；
3. Use roller to evenly coat the material.
4、第一遍塗層幹固後，再施工第二次面塗層。
4. Once the first coating is dry and solid, then the second surface coating is then constructed.
5、自流平面塗用鏝刀刮鏝一遍
5, self flow flat coated trowel scraping again.
6、註意先後施工交接處的處理；塗層要求均勻，無流掛。
6. Attention should be paid to the treatment of the successively constructed juncture.
檢驗方法：地面色澤均勻、無流掛、無針孔、光潔、平整。
Test method: uniform color, no hang, no pinhole, smooth and smooth.