生物質熱風爐怎麼不能自動傳送

生物質熱風爐怎麼不能自動傳送？1.生物質熱風爐穿帶不正確。打開右門，按照說明書標明成都收賬“穿帶過程法”或穿帶示意圖，正確穿帶。2.生物質熱風爐送帶長度控制成都找人公司電位器在零位。送帶長度控制電位器在前面板開關牌上左起第二個位置。順時針方向調整，則出帶長度長反之則短；如果在零位置則不出帶。
How can the biomass hot stove not be transmitted automatically? 1. the wearing of biomass hot stove is incorrect. Open the right door and wear the belt correctly according to the instructions of the tape or the sketch map. 2. the potentiometer of the length control of biomass hot blast stove is zero. The belt length control potentiometer is left in second positions on the front panel switch board. If the clockwise direction is adjusted, the length of the strip will be long and vice versa; if it is in the zero position, it will not be taken out.
3.選用成都收賬PP帶太厚或太薄。
3. the PP belt is too thick or too thin.
因PP打包帶生產廠傢有很多，厚度也不一致，應按要求選用；如不可能請按照說明書第十頁之方法，仔細調整送退帶滾輪之間隙。
Because PP packing belt manufacturers have many, thickness is not the same, should be se环氧地坪lected according to the requirements; if not possible, please follow the method of page 10 of the instructions, carefully adjust the gap between the feeding and returning rollers.
4.上下分機內有異物。
4. there are foreign objects in the extension.
生物質熱風爐器長期使用，又未能及時清潔與保養，致使機器內積有贓物，使送帶不順暢自如，應多作清潔保養。
The long-term use of biomass hot-blast stove fails to be cleaned and maintained in time, resulting in the accumulation of stolen goods in the machine, which makes the delivery not smooth and comfortable, and should be cleaned and maintained more.
5.送帶滾輪間隙不正確。
5. the belt gap is incorrect.
一對半自動生物質熱風爐送帶滾輪之間收賬間隙大小對正常送帶至關重要，間隙成都找人公司調整參照說明書第10頁之說明。仔細調整，調至送帶滾輪間隙隻比帶子厚度多出0.05~1mm時即可。
The clearance between the feeding rollers of a pair of semi-automatic biomass hot blast stoves is very important for normal feeding. The adjustment of the clearance refers to the instructions on page 10 of the manual. Carefully adjust, transfer to the belt roller clearance only more than the thickness of the belt 0.05~1mm.
6.電磁鐵工作不正常。
6. electromagnet work is not normal.
電磁鐵不工作。首先檢查電磁鐵連線焊接頭是否脫落，再檢查線圈是否燒壞。如兩者都無異常，應檢查電磁鐵是否位移，或是被贓物堵住，使子彈頭不能活動自如.
The electromagnet does not work. First check whether the soldering head of the solenoid is falling off, and check if the coil is burnt out. If neither of them印花地坪 is abnormal, check whether the electromagnet is displaced or blocked by stolen goods, so that the bullet can not move freely.